Strip the failed coat and start fresh
Paver Restoration and Resealing in Whitehouse, FL
Call (904) 875-8988 and a local contractor will price restoring your cloudy, peeling Whitehouse pavers.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Who restores pavers with failed sealer in Whitehouse?
A local contractor restores and reseals pavers across Whitehouse, FL, and a reply usually lands within a business day, often in a couple of hours. The estimate is free, and you can say no. To start, call (904) 875-8988.
A coat that has gone cloudy, flaky or patchy does not protect anything, and putting more on top of it makes things worse. Restoration takes the old coat off, washes the pavers, refills the joints and seals again, a process that suits pavers sealed years ago. After a restoration, a driveway that looked tired and blotchy should look even again. Describe the color and texture of the pavers when you ask for a free estimate.
How do I know I need a restoration and not just a reseal?
A reseal works when the old coat is still sound. Stallone's Pro Wash says that when water soaks in quickly instead of beading, a fresh coat is due. Restoration is for coats that have failed. Peter's Pressure Washing says failed sealer turns white, cloudy or hazy, and lists trapped water vapor, an overly thick coat, poor prep and an incompatible product as causes. To have yours judged, call (904) 875-8988.
Empty joints push a job toward restoration too. Safe Touch says empty joints or failed sealer make a two-day restoration. If your joints are low, sand is washing out after storms, or sealer is lifting in flakes, mention each one when you ask for a free estimate.
What does stripping old sealer involve?
Peter's Pressure Washing, a Tampa company, describes it in order. A stripper breaks the bond between the old sealer and the paver, and a surface cleaner with vacuum recovery lifts the sealer and the stripper away. The page says the old coat has to be fully removed before sealing again. Ask any contractor how the runoff is handled. For that conversation, call (904) 875-8988.
Safe Touch makes the same call: failed sealer is stripped, not covered. It says sealing over it traps the problem and the coat peels again. Stripping is why a restoration costs more than a standard reseal, and why it is quoted after a visit. To book that visit, ask for a free estimate.
What happens after the old coat is gone?
Joint sand is next. Peter's Pressure Washing refills worn joints with angular silica sand and packs it in. Stripping and washing pull sand out, so this step is part of nearly every restoration. Belgard says joints should be kept topped off so the bedding layer below does not break down. Ask how the sand will be set when you ask for a free estimate.
Then the new coat goes on. Peter's Pressure Washing describes a flood coat followed by a top coat of one product. Belgard warns against stacking: sealer no more than once every three years, and two coats at most over the life of a surface. Keep that in mind when a bid mentions several coats, and call (904) 875-8988 if it seems like too many.
Where else near Whitehouse can pavers be restored?
Contractors who restore pavers travel across far west Duval County and into the neighborhoods below. Each has its own page. Your street can be priced even when it has no page of its own, so call (904) 875-8988 to ask.
What does paver restoration cost in Whitehouse?
No page read for this site prices restoration per square foot, so the table below is built from published pieces. Stallone's Pro Wash, a Northeast Florida company, lists cleaning from $0.22 and sealing from $1.90 per square foot. Safe Touch, which washes pavers in Duval County, posts $1.75 to $3.25 for the full clean, sand and seal, and says strip and reseal costs more when the coat has failed. For a number on your drive, ask for a free estimate.
| Paved area | Sealing only, from $1.90 | Clean, sand and seal, $1.75 to $3.25 | Stripping the old coat |
|---|---|---|---|
| 500 sq ft | $950 | $875 to $1,625 | Quoted on the visit |
| 1,000 sq ft | $1,900 | $1,750 to $3,250 | Quoted on the visit |
| 2,000 sq ft | $3,800 | $3,500 to $6,500 | Quoted on the visit |
Each price column multiplies the rate by the area. Stripping adds to the totals, and large areas may bring the rate per foot down.
How long does a restoration take?
Plan on two days. Safe Touch says failed sealer or empty joints turn the work into a two-day restoration, with stripping and washing first and the sealer last. Unilock asks for a few hours of drying in warm sun or about 24 hours in cool shade after cleaning, and 24 to 48 hours of clear skies around the coat. To fit it around the weather, call (904) 875-8988.
Heat matters on day two. Unilock lists 50 to 90 degrees as the working range, with 75 the sweet spot, and says pavers that are too hot can stain and peel early. In Duval County that points to cooler mornings in summer. Ask how the contractor will schedule a hot week when you ask for a free estimate.
What finish should I choose when pavers are resealed?
Stallone's Pro Wash applies sealer in four finishes: wet look high gloss, wet look satin, natural matte and a natural stone penetrating one. Unilock says water-based products are easier to clean up and tend to give a lower gloss, while solvent-based ones give a high shine and need perfectly dry pavers. High sheen can be slippery when wet. Tell the contractor if the area is near the pool when you ask for a free estimate.
Will a restored driveway last, and how often is a reseal due?
Unilock and Belgard both put the cycle at three to five years, and Stallone's Pro Wash says two to five in Northeast Florida. Open sun, chlorine and summer storms pull a coat toward the short end, as Safe Touch notes. Staying on the schedule is cheaper than waiting for another failure. To plan the next one, call (904) 875-8988.
What do restored pavers look like around Whitehouse?
Why hire a contractor who works near Whitehouse?
Restoration depends on judgment, and judgment depends on having seen how pavers age here. Local contractors know the sun, humidity and sandy base that wear coats down. The estimate is free and the decision is yours. To start, ask for a free estimate.
A contractor who works out here
A company that covers Whitehouse already works in far west Duval County. Your first visit then starts from local knowledge instead of guesses.
Nothing to pay for a quote
The look at your pavers and the estimate cost nothing. Should the price not work for you, decline and nothing is owed.
Published rates to measure against
Paver companies across Northeast Florida publish their per square foot rates, and this site passes those ranges along. If a bid lands far outside those numbers, ask what explains the gap.
Your pace, your decision
Have the price written down, and take as long as you like to think it over. The contractor standards page covers what to verify before you sign.
What do Whitehouse homeowners ask before paver restoration?
How much do people charge to seal pavers?
Safe Touch, a Duval County washing company, charges $1.75 to $3.25 per square foot to clean, sand and seal. Stallone's Pro Wash lists sealing from $1.90 per square foot. A restoration costs more because the failed coat has to come off first.
Why did my pavers turn white?
Two causes are common. New pavers can show efflorescence, a salt haze that Unilock says takes 2 to 3 months and up to a year to clear. Pavers that were sealed can turn white, cloudy or hazy when the coat is trapped water, too thick, laid on a dirty surface or an incompatible product, as Peter's Pressure Washing explains.
Is it good to seal pavers in Florida?
In most cases, yes. A coat helps hold joint sand through summer storms and makes mildew easier to rinse off. The cost is another visit every few years, and a restoration is what happens when the coat is left until it fails.
Why is paver sealing so expensive?
The sealer is a small part of the job. Restoration adds stripping, a deep wash, joint sand and drying time. Safe Touch says empty joints or failed sealer turn the work into a two-day job.
Can new sealer go over the old coat on my Whitehouse pavers?
Not if the old coat has failed. Safe Touch says failed sealer is stripped first, because coating over it traps the problem and it peels again. Unilock adds that an incompatible old product can leave a whitish film.
How long does a paver restoration take?
Safe Touch says empty joints or failed sealer make it a two-day job. Stripping, washing and refilling the joints come first, and Unilock asks for 24 hours of dry time after cleaning in cool or shaded spots before any sealer.
How much does paver restoration cost in Whitehouse?
No page read for this site prices restoration by the square foot. The figures that exist are $0.22 for cleaning and $1.90 for sealing from Stallone's Pro Wash, and $1.75 to $3.25 for the full clean, sand and seal from Safe Touch, with stripping added on top and quoted on a visit.
How often should a restored driveway be resealed?
Plan on 3 to 5 years, the cycle Unilock and Belgard both give. Belgard says sealer should go on no more than once every three years, with two coats at most over the life of the surface, because stacked coats form a film that can discolor in sunlight.
Do restored pavers need new joint sand?
Usually. Peter's Pressure Washing refills worn joint sand as part of its restoration, and Belgard says joints should be kept topped off so the bedding layer below does not wash out. Stripping and washing both pull sand from the joints.
What does failed sealer look like?
Peter's Pressure Washing says it turns white, cloudy or hazy. Other signs are peeling flakes, a patchy sheen and water that soaks in rather than beading, which Stallone's Pro Wash treats as a sign a fresh coat is due.
Want your pavers restored and resealed?
Call or send the brief form. A contractor answers within 1 business day, and the estimate costs nothing.
Free, no obligation